Q3HB220M 3-phase stepper motor driver

Q3HB220M 3-phase stepper motor driver

Model No.︰Q3HB220M

Brand Name︰JB

Country of Origin︰China

Unit Price︰-

Minimum Order︰1 pc

Inquire Now

Product Description

Q3HB220M is a Constant angle, constant torque microstep driver supplies regulated phase current for supply voltage from 110V to 220V AC. It is designed for use with the 3-phase hybrid stepper motor of all kinds with 86mm to 110mm outside diameter and 5.2is a constant angle and constant torque stepper motor drive. The driven voltage range from AC110V to 220V. It can match 3-phase hybrid stepper motors whose rated current is under 7.0Aand shaft diameter range from 86mm to 130mm. Owe to bipolar constant chopping circuit, it can make motors low noise and operated smoothly when low speed; the torque is much greater than 2-phase and 5-phase stepper motor when high speed. It is widely used in small-sized numerical control device suchas medical machine, robot, instrumentation, curving machine, laser labeling machine, inner laser curving machine.

Feature

●      High performance, low price
●      16 channels constant angle and constant torque, the highest subdivision is 60000s/r
●      Highest response frequency: 200Kpps
●      The motor phase current is reduced to setting value 100ms after receiving the last pulse edge
●      Bipolar constant current chopping circuit
●      Opto-isolated input/output
●      Driven current is adjustable in 16 channels from 0.6A/phase to 7.0A/phase
●      Single power supply, voltage arrange from AC110V to220V
●      Phase remembering function (The driver remembers motor’s phase when there’s no input pulse is received for 5s and it recovers the motor’s phase when the power on or signal MF is inactive)
Current setting
1.       STOP/Im is the rotary switch that can set output current of holding motor status as 20%-80% of normal output current (increase in CW, decrease in CCW).
2.       RUN/Im is the rotary switch for adjustment of the motor current.

 

R-1
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
Im (A)
0.6
1.1
1.5
2.0
2.5
2.9
3.2
3.6
4
4.5
5
5.5
5.8
6.3
6.6
7.0

 

 
Subdivision setting
Q3HB220M drive has two groups of subdivision, each group has 16 channels set by switch SK1/SK2.

 

SK1
F
E
D
C
B
A
9
8
7
6
5
4
3
2
1
0
s/r
400
500
600
800
1000
1200
2000
3000
4000
5000
6000
10000
12000
20000
30000
60000

 

SK2 is the second group. The subdivision setting of SK2 is the same as SK1.
Choose SK1 group when subdivision choosing signal SM is at low voltage and SK2 at high voltage.

Wiring example

 
Caution
1.       Please don’t reverse the power supply, supply voltage shouldn’t exceed AC220V.
2.       Input control signal is 5V, current-limiting resistance should be connected when over 5V.
3.       Alarm indicator lights and the drive shuts off if the drive temperature is over 70℃. It doesn’t work until the temperature falls to 50℃. The heat sink is needed when overheat occurs.
4.       Alarm indicator lights when overcurrent (short of load) occurs. Please check motor’s connection and other shorts and turn the power supply on after removing the trouble.
5.       Alarm indicator lights when undervoltage (the voltage is less than AC110V) occurs.

Parameter switch function

 

DP3
OFF, double pulse: PU is positive pulse signal, DR is negative pulse signal
ON, single pulse: PU is pulse signal, DR is direction signal
DP4
Self detect switch (OFF: accept pulse input, ON: send out 7.5KHz pulse. The subdivision should be between 2000-10000 s/r)

 

 
Input signal oscillogram
 
 
 
Terminal function
Mark
Function
Specification
MF+
Positive of opto-isolated
Connected to +5V power supply. Driven voltage range from +5V to +24V. Current-limiting resistance is needed when over 5V.
MF-
Motor free signal
The motor current will be cut off and the drive stops working when it effects.
SM+
Positive of opto-isolated
Connected to +5V power supply. Driven voltage range from +5V to +24V. Current-limiting resistance is needed when over 5V.
SM-
Subdivision choosing signal
Choose subdivision by SK1 when low voltage and SK2 when high voltage. Input resistance is 220Ω.
DR+
Positive of opto-isolated
Connected to +5V power supply. Driven voltage range from +5V to +24V. Current-limiting resistance is needed when over 5V.
DR-
DP3=ON, DR is direction signal
Change the motor’s direction of rotation. Input resistance is 220Ω. Low voltage 0-0.5V, high voltage 4-5V, pulse width>2.5μS
DP1=OFF, DR is negative pulse signal
PU+
Positive of opto-isolated
Connected to +5V power supply. Driven voltage range from +5V to +24V. Current-limiting resistance is needed when over 5V.
PU-
DP3=ON, PU is pulse signal
With the falling edge of the signal PU, the motor executes an angular step. The input resistance is 220Ω. Low voltage 0-0.5V, high voltage 4-5V, pulse width>2.5μS.
DP3=OFF, PU is positive pulse signal
TM+
Positive of opto-isolated origin output signal
When the motor current is on, the motor is at the origin position. Opto-isolated output (high voltage). Connect TM+ to current-limiting resistance, TM- to ground. The maximum driven current is 50mA, the highest driven voltage is 50V.
TM-
Negative of opto-isolated origin output signal
RDY+
Positive of opto-isolated ready signal
It is active (low voltage) when the drive is ready for receiving controller’s signal.
RDY-
Negative of opto-isolated ready siangl
 
~AC
Power supply
AC110V~220V
U
Connection
V
W

Payment Terms︰ Paypal,bank transfer,TT/LC/DP/DA